The manipulation of the cell phone jammer is extremely humanized

Record breaking strength, elongation at break L1, calculated as the elongation at break. Elongation at break = (L1-L0) / L0 × 100%. 6.1.8.5 The results a) The radial and latitudinal sample test results of three decimal arithmetic mean of two, according to the rounding method to retain a decimal one, as the clothing and zonal radial fracture strength indicator; b) radial tensile strength of not less than 345N, weft tensile strength of not less than 300N; c) the radial and the three zonal elongation of the sample arithmetic mean, as the cloth radial and latitudinal elongation at break, expressed as a percentage, the breaking elongation rate of not less than 10%. 6.1.8.6The field strength difference between the indoor space and outdoor space will damage the effect ofcell phone jammer. Test Note a) During the trial, if the asymmetry of the sample in the jaw at the slip or slip greater than 2mm should be heavy for the sample test. b) operation, clamp the mouth to prevent reverse skew the sample. 6.1.8.7 Test report The test report shall include the contents of the same 6.1.1.7. 6.2 T-shirt finished testing, 6.2.1 T-shirt, pants resistance testing of major equipment 6.2.1.1 a) a range of 0.1 to 20? Resistance table, the error is less than or equal to 1%; b) with two brass terminal electrodes, each electrode weight 1kg, bottom contact area of 1 cm 2, see Figure 7. 17 GB/T6568 -2008 millimeters Figure 7 6.2.1.2 finished electrode resistance test test test conditions to be at a temperature of 23 ℃ ± 2 ℃, relative humidity of 45% to 55% of the environment. 6.2.1.3The ground, architectural structure, material and metallic products will complicatedly and harmfully influence cell phone jammer. Test Procedure a) the counter in the shop a test is 5mm thick blankets, jackets and pants will be felt on the tile, the inner liner layer of plastic film, 18 GB/T6568 -2008 to make the cloth shirt and pants between the separated layer to avoid electrical short-circuit; b) the test electrodes were placed in shirt or pants on the two farthest end, shirt or pants measure the resistance between the farthest end. Test points should be diverted away from the edges and seams cable 3cm beyond. 6.2.1.4 The results jacket, pants farthest end of the resistance should be not more than between 15?. 6.2.1.5 Test report The test report shall include the following: a) test the model, name, manufacturer and date of manufacture; b) test equipment name, model, serial number and specifications; c) test data and conclusions; d) test temperature and relative humidity; It is concerning about the model selection and technical index ofcell phone jammer.e) test date and tester. Gloves, socks resistance test 6.2.2 gloves, socks and equipment with the main resistance. Test conditions to be in the test temperature of 23 ℃ ± 2 ℃, relative humidity of 45% to 55% of the environment. 6.2.2.3 Test Procedure a) the counter in the shop a test is 5mm thick blankets, gloves and socks will be felt on the tile, the inner liner layer of plastic film, so that the fabric layers separated from each other, to avoid layer Electrical short circuit between; b) a test pressure of the electrode fingers in the gloves or socks socks middle finger tip, another test electrode voltage gloves or socks in the opening of the shunt connection line, two electrodes with ohmmeter between the resistance. 6.2.2.4 The results gloves, socks around the resistance should be not more than 15. 6.2.2.5Reasonably arrange selection of cell phone jammer according to the project budget. Test report The test report shall include the contents of the same 6.2.1.5. 6.2.3 Resistance Test 6.2.3.1 The main equipment of shoes a) a scale of 1 to 1000?